1 of 5 ? 2016 te connectivity family of companies all rights reserved *trademark te connectivity, te connectivity (logo), and te (logo) are trademarks. other logos, product, and/or company names may be tra demarks of their respective owners. product information 1 - 800 - 522 - 6752 this controlled document is subject to change. for latest revision and regional customer service, visit our website at www.te.com. instruction sheet 408 - 32181 19 feb 16 rev b extraction tool cage assembly configuration 2215067 - 1 1 x 6 (sfp+ external emi springs with light pipes) 2215067 - 2 1 x 1 (sfp with light pipes) 2215067 - 3 1 x 2 2215067 - 4 1 x 3 2215067 - 5 1 x 4 2215067 - 6 1 x 5 2215067 - 7 1 x 7 2215067 - 8 1 x 8 2215067 - 9 1 x 4 (sfp+ enhanced, emi gasket with heat sink & light pipes) 1 - 2215067 - 0 1 x 1 (sfp+ external emi springs with heat sink & light pipes) figure 1 1. introduction s fp style extraction tool kits 2215067 - [ ] are used to remove the printed circuit (pc ) board from sfp connector and cage assemblies with external emi springs and heat sinks and light pipes described in figure 1. the cage assemblies contain press - fit contacts. read these instructions thoroughly before using the extraction tool kit. note dimensions on this sheet are in metric units [with u.s. customary units in brackets]. figures and illustrations are for reference only and are not drawn to scale. sma ll form - factor pluggable (sfp style) extraction tool kit 2215067 - [ ] cage assemblies extraction tool top push plate wall supports finger mounting block base plate 1 x 6 sfp+ cage assembly 2170509 - 1 printed circuit (pc) board (ref) original instructions
408 - 32181 rev b 2 of 5 2. description each extraction tool kit consists of an extraction tool, a top push plate, base plate, and wall supp orts (one for each stacked row of the cage assembly). the base plate features a finger mou nting block that holds up to eight wall supports to the base plate. see figure 1. the top push plate is designed to be installed onto the upper tooling and the base p late is designed to be installed onto the lower tooling of the application tool. the extraction tool has cutouts (one located on each side) to accept the protruding part of the cage assembly. each finger of a wall support fits into a port of the cage ass embly. during extraction, the back and sides of the extraction tool protect the cage assembly from damage, the wall supports support the individual ports of the cage assembly, and the top push plate provides a surface to apply an even force to extract the pc board from the connector and cage assembly. 3. application tooling requirement power for the extraction tool must be provided by application tools (with a ram) capable of supplying a downward force of 44.5 n [10 lb. ] per contact. manual arbor frame assembl y 58024 - 1 is available for use with these extraction tool kits. refer to instruction sheet 408 - 6923 for operating procedure. caution over - driving of the extraction tool could cause damage to the connector or cage assembly. 4. extraction procedure 1. ensure that the amount of wall supports installed onto the finger mounting block matches the amount of ports of the cage assembly. it is recommended to center the group of wall supports on the finger mounting block. refer to figure 1. 2. install the top push plate onto the upper tooling and the base plate (with the wall supports) onto the lower tooling of the application tool. see figure 2. c aution ensure that the upper tooling and lower tooling are secure; otherwise, damage to the connector and cage assembly could occur. 3. place the open end of the extraction tool over the cage assembly so that the cutouts align with the protruding part (at the back) of the cage assembly. make sure that the sides of the extraction tool sit on the pc board. 4. slide the extraction tool (with the connector and cage assembly and pc board) onto the wall supports so that each finger of each wall support enters a port of the cage assembly. make sure the fingers are fully inserted into the ports. see figure 2. figure 2 side view application tool ram fingers of wall supports fully inserted into cage assembly base plate (with wall supports) lower tooling of application tooling pc board top push plate sides of extraction tool sitting on pc board
408 - 32181 rev b 3 of 5 5. cycle the application tool to extract the pc board from the connector and cage assembly. then retract the ram, and carefully remove the ext raction tool (with the connector and cage assembly) from the wall supports. 5. maintenance and insp ection the extraction tool kit is inspected before shipment. it is recommended that the extraction tool kit be inspected immediately upon arrival at your facili ty to ensure that it has not been damaged during shipment and that it conforms to the dimensions provided in figure 3. 5.1. daily maintenance it is recommended that each operator be made aware of, and responsible for, the following steps of daily maintenance: 1. remove dust, moisture, and contaminants with a clean, soft brush or a lint - free cloth. do not use objects that could damage the extraction tool kits components. 2. when the extraction tool kit is not in use, store it in a clean, dry area. 5.2. periodic inspection regular inspections should be performed by quality control personnel. a record of scheduled inspections should remain with the extraction tool kit or be supplied to personnel responsible for the extraction tool kit. inspection frequency should be based on amount of use, working conditions, operator training and skill, and established standards. 6. replacement and repa ir customer - replaceable parts are listed in figure 3. a complete inventory should be stocked and controlled to prevent lost time when replacement of parts is necessary. parts other than those listed should be replaced by te connectivity to ensure quality and reliability. order replacement parts through your te representative, or call 1 - 800 - 526 - 5142, or send a facsimile of your purchase order to 717 - 986 - 7605, or write to: customer service (038 - 035 ) tyco electronics corporation po box 3608 harrisburg pa 17105 - 3608 7. revision summary ? updated document to corporate requirements ? added new information to table in figures 1 and 3. ? added new text to sections 1 and 2. ? changed dimension in figure 3.
408 - 32181 rev b 4 of 5 figure 3 (contd) a 40.4 [1.591] 6.00 [.236 ] 44.50 [1.75 2] 142.85 [5.624] 101.6 [4.00] 40.4 [1.591] 50.8 [2.00] 50.8 [2.00] 25.4 [1.00] 40.36 [1.589 ] 5 1 2 3 4 6 37.00 [1.456 ] 7 130.15 [5.125 ] 76.2 [3.00]
408 - 32181 rev b 5 of 5 tool (by kit part number) dimension a dimension b 2215067 - 1 91.00 [3.583] 37.00 [1.456] 2215067 - 2 19.75 [.778] 2215067 - 3 34.00 [1.339] 2215067 - 4 48.25 [1.900] 2215067 - 5 62.50 [2.461] 2215067 - 6 76.75 [3.022] 2215067 - 7 105.25 [4.144] 2215067 - 8 119.50 [4.705] 2215067 - 9 62.50 [2.461] 1 - 2215067 - 0 19.75 [.778] 42.00 [1.654] item no. description qty per tool 1 x 1 1 x 2 1 x 3 1 x 4 1 x 5 1 x 6 1 x 7 1 x 8 1 plate, top push 1 1 1 1 1 1 1 1 2 plate, base 1 1 1 1 1 1 1 1 3 support, wall 1 2 3 4 5 6 7 8 4 mounting block, finger 1 1 1 1 1 1 1 1 5 plate, side 2 2 2 2 2 2 2 2 6 block, center 1 1 1 1 1 1 1 1 7 plate, rear 1 1 1 1 1 1 1 1 item no. extraction tool kit part number 2215067 - 1 2215067 - 2 2215067 - 3 2215067 - 4 2215067 - 5 2215067 - 6 2215067 - 7 2215067 - 8 2215067 - 9 1 - 2215067 - 0 1 2161356 - 1 2161356 - 1 2161356 - 1 2161356 - 1 2161356 - 1 2161356 - 1 2161356 - 1 2161356 - 1 2161356 - 1 2161356 - 1 2 2161354 - 1 2161354 - 1 2161354 - 1 2161354 - 1 2161354 - 1 2161354 - 1 2161354 - 1 2161354 - 1 2161354 - 1 2161354 - 1 3 2215807 - 1 2215807 - 1 2215807 - 1 2215807 - 1 2215807 - 1 2215807 - 1 2215807 - 1 2215807 - 1 2215807 - 1 2215807 - 1 4 2215806 - 1 2215806 - 1 2215806 - 1 2215806 - 1 2215806 - 1 2215806 - 1 2215806 - 1 2215806 - 1 2215806 - 1 2215806 - 1 5 2215809 - 1 2215809 - 1 2215809 - 1 2215809 - 1 2215809 - 1 2215809 - 1 2215809 - 1 2215809 - 1 2215809 - 1 2215809 - 2 6 2215810 - 1 2215810 - 2 2215810 - 3 2215810 - 4 2215810 - 5 2215810 - 6 2215810 - 7 2215810 - 8 2215810 - 5 2215810 - 2 7 2215808 - 1 2215808 - 2 2215808 - 3 2215808 - 4 2215808 - 5 2215808 - 6 2215808 - 7 2215808 - 8 2215882 - 1 2215808 - 9 figure 3 (end)
|
